Can I Repair My Termina Fishing Rod

Download Commodity

Download Article

Modern fishing rods don't break easily, merely they can be fixed hands with a few simple tools you may have at home. If your rod snapped, you can mend it together with a fiberglass pole and epoxy to hide the break. When one of the guides breaks, you tin remove information technology and wrap a new one in its place. Yous can change rod tips if they snap or intermission too. With a little bit of piece of work, yous tin fix your rod so it'south as expert as new!

1
Sand or cut the broken ends of the rod so they're affluent. Use 180- or 220-grit sandpaper to smooth the ends so they fit together hands if the rod has a clean break. If your fishing rod has a jagged edge, then use a pair of scissors to cut the sharp edges off of the end of the rod so the pieces are flush. After you lot brand your cut, utilise sandpaper to smooth out the edges and roughen upward the surface.^[ane]
- Jagged edges are weaker and are more likely to intermission again than edges that are flush with one another.
2
Measure the circumference of the rod. Use a flexible tape measure and wrap it around the broken stop of your fishing rod. And so measure the circumference on the other slice of your line-fishing rod to see if it's skinnier. Write down your measurements and so you know what pole size you need for fixing your rod.^[ii]
- You lot tin can also measure out the diameter of the rod on both of the broken ends if you don't have a flexible measuring tape.
Advertisement
3
Cut a piece of fiberglass pole so it'south about 12 in (30 cm) long. Get a fiberglass pole that has a circumference that's almost ^ane⁄₈ – ¹⁄_iv inch (0.32–0.64 cm) smaller than your line-fishing rod. Use a hacksaw to cut out a 12 in (30 cm) department of the pole so it tin can fit inside your fishing rod and support the rod without breaking.^[three]
- You can buy fiberglass poles from your local hardware store. Information technology doesn't affair what color yous utilise since it will fit inside of the rod.
- If your angling rod isn't hollow, and then using a fiberglass pole won't piece of work. You can either try to record your rod back together or get a new one.
Tip: You can also cut a section off of an old fishing pole that you don't use anymore if you don't accept a fiberglass rod.
4
Slide the fiberglass pole into i side of the fishing rod. Hold your rod horizontally and so you tin position the fiberglass pole in the rod without it sliding too far. Push one finish of the fiberglass pole into the end of the rod with the handle. Continue sliding the pole into the fishing rod until there's 6 inches (15 cm) sticking out from the finish.^[4]
- If the pole doesn't fit snugly inside the fishing rod, then wrap the pole with duct or masking record to brand it thicker.
v
Apply 2-part epoxy to the exposed side of the fiberglass pole. Open up your 2-part epoxy and cascade it into a basin. Employ a paintbrush to spread a sparse layer of the epoxy on the exposed end of the fiberglass pole. Once the 2-part epoxy is mixed, work quickly so information technology doesn't dry or set earlier you lot put your rod back together.^[5]
- You can buy two-part epoxy from any hardware or craft store.
half dozen
Slide the other part of the rod onto the fiberglass and let it dry. Slowly push the other end of your rod onto the exposed end of the fiberglass pole. Make sure the guides on the pole line upward with i another so your line doesn't become tangled when you try using your pole again. Push the 2 pieces of the rod together so they're flush. Let the epoxy set overnight so it firmly adheres to the rod.^[6]
- The epoxy doesn't ready right away, and then you lot can still rotate or motion the rod pieces once you slide them together.
- If any epoxy comes out of the joint while you're sliding the pieces together, moisture your finger and smoothen out the epoxy and then it isn't every bit visible.
- Wrap a layer of electrical tape effectually the seam if you lot want an additional layer of security.
Advertisement

1
Cut the tape or thread around the broken guide with a razor blade. Utilize a straight razor blade or a craft knife to remove whatsoever threading that may be surrounding the rod guide. If it's difficult to remove using just a blade, then effort heating the area for 3-four seconds with a lighter to loosen whatsoever of the adhesives. Peel off the tape and unwind the threading until the old, broken guide comes off of the rod.^[7]
- Rod guides are the circular metallic pieces forth the length of the rod that help go on your line straight.
- Be careful non to rut the rod for besides long since it could crusade damage to it.
- Don't cutting into the rod with your razor, or else you could damage it and make information technology weaker.
2
Sand the rod and foot of the new guide to go better adhesion. Use 120- or 220-grit sandpaper to get rid of whatsoever leftover adhesive and to add tooth to the rod. Rub all the mode around the rod on the spot where you want to place the new guide. Then, utilize your sandpaper on the foot of the guide, which is the flat role that rests against the line-fishing rod.^[eight]
- You can buy new fishing guides at sporting skilful stores. Make certain the new guide is the aforementioned size and style as the other guides on your fishing rod or else your line may snag or go tangled.
3
Tape the new guide onto the rod so information technology'due south aligned. Press the foot of the new guide onto the rod so it'south in line with the other guides. Rip off a sparse slice of masking tape and wrap it around the human foot so it'southward held in identify. That way, yous don't need to keep belongings it in place while yous wrap it.^[9]
- Y'all can also use super glue, but information technology volition be difficult to move or readjust once the glue is gear up.
4
Wrap the human foot of the guide with thread to hold information technology in identify. Whatever type of thread volition work for wrapping your guide onto the rod. Loop your threading around the rod so it's ^one⁄_ii – ³⁄₄ inch (i.3–ane.9 cm) from the guide'southward foot on the side closest to the handle. Maintain tension on the loop and start tightly winding the thread effectually the rod. Make sure the thread doesn't overlap with loops yous've already made and that they are flush with 1 another.^[ten]
- Take the piece of tape off of the foot you lot've wrapped everything beneath it.
Tip: Use a thread that matches the color of your rod if you desire it to blend in.
5
Place a looped piece of thread over the wrap when in that location's ¹⁄₈ in (0.32 cm) left. When your wrapping is ¹⁄₈ inch (0.32 cm) from the circular office of the guide, stop winding the thread around the pole. Cut a separate slice of thread so it's near 6 inches (xv cm) long and fold it in half to grade a loop. Lay the 2d piece of thread on height of your wrapping so the loop sticks out nigh your guide.^[11]
- If yous don't have whatsoever other thread, you lot can also use a thin fishing line instead.
half dozen

Wrap the concluding ¹⁄₈ in (0.32 cm) over the 2d slice of thread. Once the looped piece of thread is on peak of the wrapping, continue spinning your thread effectually the human foot of the guide. Proceed wrapping the terminal ¹⁄₈ inch (0.32 cm) of the guide and then the heart of the looped piece is held against the rod.^[12]
7
Feed the thread through the looped piece and pull it tight. Once you attain the stop of your wrapping, cut the end of the thread you used to wrap and pull information technology through the middle of the loop. Pull the other cease of the looped piece downwards and away from the guide to pull the thread underneath the wrapping. This way, the wrapping is secured to the rod without having to necktie a knot.^[13]
- If you don't want to use a looped piece of thread, you can besides try tying a knot in the threading, but information technology may not exist as potent and information technology could be more difficult.
8
Pigment 2-role epoxy onto the thread and let information technology dry. Mix the 2 parts of the epoxy in a small dish with a paintbrush until they are thoroughly combined. Pigment a thin layer of the epoxy over your threading so it hardens and stays in identify. Keep the rod horizontal and allow information technology dry out overnight before you lot try using your rod again.^[14]
- Work quickly with the epoxy since information technology will apace first to dry and harden once you lot mix it.
Advert

1
Heat the tip top of your line-fishing rod with a lighter to loosen the adhesive. Set the rod horizontal so you can hands achieve the tip. Concur a lighter underneath the tip top of the rod, which is the ringed slice at the finish of the rod, and heat it up for four-5 seconds at a time. Once it's heated, try pulling it off with a pair of pliers or by paw. If it doesn't come off easily, endeavor heating it for another few seconds.^[15]
- Heating the tip top helps loosen the adhesive holding information technology in identify and so it'due south easier to remove.
- If the tip snapped off of your rod, then you can remove the quondam tip height from the broken piece or yous can skip this step.
two

Shine the tip of the rod with sandpaper to remove whatsoever shards. Rub the exposed tip of the rod with 120- or 220-grit sandpaper to smooth information technology out. Rotate the rod around the sandpaper until the tip is smooth and affluent. It's okay if in that location are modest abrasion marks on the rod tip since it will have meliorate adhesion to the new tip top.^[16]

Tip: If sandpaper isn't enough to remove the shards on the end of your angling rod, then carefully cutting off the ends with a scissors.
3
Cutting pieces of rod cement into strips that fit inside your new tip top. Rod cement is an adhesive that comes in a solid block and is used for fishing rods to hold guides and tips in place. Use a razor or craft knife to cut out small strips of the rod cement and so they fit inside the hollow chamber on your rod tip pinnacle.^[17]
- You can buy rod cement and new tip tops from your local sporting goods shop or online.
4

Melt the rod cement inside the tip top with your lighter. Agree the new tip top with a pair of pliers and put the pieces of rod cement in the hollow tube at the end of it. Apply your lighter to estrus the rod cement for 4-five seconds and melt information technology so you can attach information technology to your rod. One time the rod cement is melted, work quickly and so it doesn't solidify again.^[eighteen]
5
Slide the tip peak onto your rod so information technology lines up with the guides and let information technology dry out. While the cement is still hot, slide it onto the tip of your rod and rotate information technology so the band is in line with the other guides. Wipe away any backlog rod cement with a piece of paper towel and let it set for at least 1-two hours. Once the cement is dry out, your rod is gear up to apply!^[19]
- If y'all need to adjust or reposition the tip top afterward the cement is dry out, then heat it again for iii-iv seconds with your lighter.
Advertising

Add New Question

Question

Where do I buy epoxy resin gum?

At whatever habitation improvement or hardware shop.

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertising

Take your rod to a fishing supply store or a repair person if you take trouble fixing it on your ain.
If you demand to ready a snapped rod in an emergency, overlap the pieces by 6 inches (xv cm) and tape them together tightly.^[20]

Thank you for submitting a tip for review!

Don't hold a flame against your rod longer than a few seconds or else you could permanently damage the rod.
Exist careful while working with razor blades so you don't accidentally cut yourself.

Things You'll Need

Scissors
Sandpaper
Tape mensurate
Fiberglass pole
Hacksaw
2-part epoxy
Bowl
Paintbrush
Electric record (optional)

Razor blade
Lighter
Sandpaper
Masking tape
Rod guides
Thread
2-part epoxy
Dish
Paintbrush

Lighter
Pliers
Sandpaper
Rod cement
Arts and crafts knife
Rod tip summit

Nearly This Article

Commodity Summary Ten

To fix a snapped fishing rod, try using a fiberglass pole and some epoxy. First, sand the snapped edges to make them flush. Smooth edges are stronger and less likely to break. Cutting a 12 inch long piece of fiberglass pole using a hacksaw. Slide one end of the pole into your fishing rod until there are 6 inches sticking out. Once the fiberglass pole fits snugly into the rod, use epoxy to the exposed terminate using a paintbrush. Connect the second half of the cleaved rod to the fiberglass pole and allow the epoxy set. To supercede the rod guide, showtime, remove any threading from effectually the guide using a craft knife. Marshal the new guide onto the rod and utilise tape to hold it in place. Wrap the new thread over the guide and and so comprehend information technology in epoxy to set information technology. For more ideas on fixing a broken line-fishing rod, like how to alter a rod tip, read on.

Did this summary help y'all?

Thanks to all authors for creating a page that has been read 210,163 times.

Did this article help you?